more

• Smart All-In-One OLED Display Modules (µOLED)
• Smart All-In-One LCD Display Modules (µLCD)
• LCD / OLED Graphics Controller Modules

More Images (click to enlarge):

µOLED-3202X-P1
2.4" and 2.8" Intelligent OLED Display Module

µOLED-3202X-P1 Features

Documents
µOLED-3202X-P1 User Manual Rev. 1.0 861KB
OLED Facts 2.69MB

4DGL Workshop

More Images (click to enlarge):

µOLED-128-G1
1.5" Intelligent OLED Display Module

µOLED-128-G1 Features

• 128 x 128 resolution, 65K true to life colours, PMOLED screen.
• 1.5” diagonal size, 45.5 x 33.5 x 6.3mm. Active Area: 27mm x 27mm.
• No backlighting with near 180° viewing angle.
• Easy 5 pin interface to any host device: VCC, TX, RX, GND, RESET
• Voltage supply from 3.6V to 6.0V, current @40mA nominal when using a 5.0V supply.
• Serial RS-232 (0V to 3.3V) with auto-baud feature (300 to 256K baud). Rx line has built in series current limit resistor and a pull-up resistor.
• Powered by the 4D Labs GOLDELOX processor (also available as separate OEM IC for volume users).
• 2 different operating platforms; the Serial Command platform (factory default) or the 4DGL (4D Graphics Language) platform.
• Optional USB to Serial interface via the 4D micro-USB (µUSB-MB5 or µUSB-CE5) modules.
• Onboard micro-SD (µSD) memory card adaptor for storing of icons, images, animations, etc. 64Mb to 2Gig µSD memory cards can be purchased separately.
• Rich set of built in graphics commands and functions.

Documents
uOLED-128-G1 User Manual Rev. 1.0 1.53MB
OLED Facts 2.69MB
uOLED Connection Diagram 13.6KB

4DGL Workshop

More Images (click to enlarge):

µOLED-160-G1
1.7" Smart OLED Display Module

This product replaces the µOLED-160-GMD1.

Documents
uOLED-160-G1 User Manual Rev. 1.0 1.53MB
OLED Facts 2.69MB
uOLED Connection Diagram 13.6KB

4DGL Workshop

More Images (click to enlarge):

µOLED-96-G1
0.96" Stamp sized Intelligent OLED module

µOLED-96-G1 Features

The µOLED-96-G1 is aimed at being integrated into a variety of different applications via a wealth of features designed to facilitate any given functionality quickly and cost effectively and thus reduce ‘time to market’. These features are as follows:

• 96x64 pixel resolution, 256 or 65K true to life colours Enhanced OLED screen.
• 0.96” diagonal. Module Size: 32.7 x 23.0 x 4.9mm. Active Display Area: 20mm x 14mm.
• No backlighting with near 180° viewing angle.
• Easy 5 pin interface to any host device: VCC, TX, RX, GND, RESET.
• Voltage supply from 3.6V to 6.0V, current @ 40mA nominal when using a 5.0V supply source.
• Serial Interface (0V to 3.3V) with auto-baud feature (300 to 256K baud).
• Powered by the 4D-LABS GOLDELOX processor (also available as separate OEM chips for volume users).
• Optional USB to Serial interface via the 4D micro-USB (µUSB-MB5 or µUSB-CE5) modules.
• Onboard micro-SD (µSD) memory card adaptor for storing of icons, images, animations, etc. 64Mb to 2Gig µSD memory cards can be purchased separately.
• Three selectable font sizes (5x7, 8x8 and 8x12) for ASCII characters as well as user-defined bitmapped characters (32 @ 8x8).
• Built in graphics commands such as: LINE, CIRCLE, RECTANGLE, TEXT, USER BITMAP, BACKGROUND COLOUR, PUT PIXEL, IMAGE, etc. just to name a few.

Documents
uOLED-96-G1 User Manual Rev. 1 1.19MB
uOLED Connection Diagram 14KB

More Images (click to enlarge):

µOLED-96-PROP
0.96" Propeller Powered OLED module

µOLED-96-PROP Features

Documents
uOLED-96-Prop User Manual Rev. 1 848KB

More Images (click to enlarge):

µLCD-32032-P1T
3.2" QVGA Touch Screen LCD

µLCD-320-PMD2
2.2" QVGA Smart LCD module

The µLCD is a compact and cost effective all in one ‘SMART' LCD module with an embedded graphics controller that will deliver ‘stand-alone’ functionality to your project. The ‘simple to use’ embedded commands not only control background colour but can produce text in a variety of sizes as well as draw shapes (which can include user definable bitmapped characters such as logos) in 256 or 65,536 colours whilst freeing up the host processor from the ‘processor hungry' screen control functions. This means a simple micro-controller with a standard serial or USB interface can drive the µLCD module with total ease.

µLCD-320-PMD2 Features

The µLCD-320-PMD2 is aimed at being integrated into a variety of different applications via a wealth of features designed to facilitate any given functionality quickly and cost effectively and thus reduce ‘time to market’. These features are as follows:

• 240 x 320 pixel resolution, 256 or 65K true to life colours, Enhanced LCD screen.
• 2.2” diagonal. Module Size: 74.5 x 40.5 x 10.3mm. Active Area: 33.75 x 45.25mm.
• LED backlighting with excellent viewing angle.
• Easy 5 pin interface to any host device: VCC, TX, RX, GND, RESET
• Voltage supply from 3.6V to 6.0V, current @ 60mA nominal when using a 5.0V supply source.
• Serial RS-232 (0V to 3.3V) with auto-baud feature (2400 to 500K baud). If interfacing to a system greater than 3.6V supply, a series resistor (1K) is required on the RX line.
• Powered by the fully integrated PICASO-MD2 module (also available as separate OEM modules for volume users).
• Optional USB to Serial interface via the 4D micro-USB (uUSB-MB5) module.
• Onboard micro-SD (µSD) memory card adaptor for storing of icons, images, animations, etc. 64Mb to 1Gig µSD memory cards can be purchased separately.
• Four selectable font sizes (5x7, 8x8 8x12 and 12x16) for ASCII characters as well as user-defined bitmapped characters.
• Built in graphics commands such as: LINE, CIRCLE, RECTANGLE, TEXT, USER BITMAP, BACKGROUND COLOUR, PUT PIXEL, IMAGE, etc. just to name a few

Documents
uLCD-320-PMD2 Users Manual Rev. 1.0 1.12MB

µLCD-320-PMD2 Serial Command Set

The heart of the µLCD-320-PMD2 is the easy to understand command set. This comprises of a handful of easy to learn instructions that can draw lines, circles, squares, etc, to provide a full text and graphical user interface. The commands are sent to the µLCD-320-PMD2 via its serial connection (5 pin header). The command set is grouped into 3 sections:
• General Command Set
• Display Specific Command Set
• Extended Command Set

NOTE:
The RX and the TX signals are at 3.3V levels. If interfacing to a host system running at voltages greater than 3.6V levels, then a 1K series resistor must be inserted between the Host TX and the µLCD-320-PMD2 RX signals as shown in the diagram on the left.

GOLDELOX-MD1
Tiny OLED-LCD Graphics Controller with micro-SD

The GOLDELOX-MD1 is a compact and cost effective all in one ‘SMART' OLED and LCD panel controller module with embedded graphics that will deliver ‘stand-alone’ functionality to your project. The ‘simple to use’ embedded commands not only control background colour but can produce text in a variety of sizes as well as draw shapes (which can include user definable bitmapped characters such as logos) in 256 or 65,536 colours whilst freeing up the host processor from the ‘processor hungry ‘ screen control functions. This means a simple micro-controller with a standard serial or USB interface can drive the module with total ease.

GOLDELOX-MD1 Features

The GOLDELOX-MD1 module is aimed at being integrated into a variety of different applications via a wealth of features designed to facilitate any given functionality quickly and cost effectively and thus reduce ‘time to market’. These features are as follows:

• Easily interface to any small to medium size monochrome or full colour graphics OLED or LCD panel that has a CPU interface with these signals directly from the module: D0-D7, RD, WR, CS, RESET, D/C
• Directly drives displays with resolutions from 96x64, 128x64, 128x128, 128x160, 160x128 up to 174x220.
• 28 pin module with a tiny footprint measuring only 19.2(L) x 20.3(W) x 5.5(H) mm
• Choose any one of the 4D range of LCD or OLED displays and with a few external components interface it directly to the GOLDELOX-MD1 module on the user application board. Then download via the serial port the specific display Personality Module Micro-Code (PmmC) file into the GOLDELOX-MD1 module.
• Voltage supply from 3.6V to 6.0V, current @ 15mA nominal when using a 5.0V supply source.
• Serial RS-232 (0V to 3.3V) with auto-baud feature (300 to 256K baud).
• Onboard micro-SD (µSD) memory card adaptor for storing of icons, images, animations, etc. 64Mb to 1Gig µSD memory cards can be purchased separately.
• Three selectable font sizes (5x7, 8x8 and 8x12) for ASCII characters as well as user-defined bitmapped characters (32 @ 8x8)
• Built in graphics commands such as: LINE, CIRCLE, RECTANGLE, TEXT, USER BITMAP, BACKGROUND COLOUR, PUT PIXEL, IMAGE, etc. just to name a few

Documents
GOLDELOX-MD1 Users Manual Rev. 1.0 1.03MB
GMD1-LCD128 Reference Design 17KB
GMD1-OLED128 Reference Design 18KB
GMD1-OLED160 Reference Design 18KB

µVGA-PICASO-MD1
(Controller only)

µVGA-PICASOMD1-UB
(Base Board Adaptor)

µVGA-PICASO-MD1 (Controller only)
Tiny VGA Graphics Controller for QVGA, VGA, SVGA

µVGA-PICASO-MD1 Features

The µVGA-PICASO-MD1 module is aimed at being integrated into a variety of different applications using a wealth of features designed to facilitate the designer to quickly and cost effectively complete a product and thus reduce ‘time to market’. These features are as follows:

• Intelligent and fully integrated VGA/SVGA Display Graphics Controller.
• Tiny 28 pin module, powered by the 4D LABS PICASO chip. A powerful DSP/Controller based multi purpose graphics engine.
• Low Power design. 3.0Volts to 3.6Volts supply @90ma.
• 256 Colours with standard resolution modes for QVGA (320x240), VGA (640x480) and SVGA (800x600, to be implemented in the near future). The μVGA-PICASO-MD1 supports multiple resolutions within the same module. Resolutions are selectable during run time under host control. Resizable viewing window allows partial/full screen control.
• The digital video signals, RED0:RED2, GREEN0:GREEN2, BLUE1:BLUE2, HSYNC, VSYNC and BLANK(R,G,B), facilitate using a simple Resistor-DAC to drive any standard VGA monitor.
• 512K bytes of onboard SRAM for video memory allows 8 pages for QVGA, 2 pages for VGA and 1 page for SVGA resolutions. Utilising the multiple pages allows double buffering which can be used for smooth animations and windowing of menu systems.
• RX and TX signals (TTL levels) provide a simple serial host interface. The serial interface allow the μVGA-PICASO-MD1 graphics module to be connected to any host controller such as a PIC, AVR, STAMP, ARM, Propeller just to name a few as well as a PC. The host controls the module by sending simple serial commands. Auto baud rate detection from 2400 baud to 1Mbit/sec.
• Powerful, easy to use and understand built in graphics functions allow drawing of lines, rectangles, circles, ellipses, text, images, icons, user defined bitmaps and much more…
• SPI signals (SDI, SDO, SCK) allow the module to be connected to a number of SD and MMC memory cards (from 64Mb up to 2Gb) that can store images, icons, and other graphics objects.
• Future upgrades and enhancements are easily achieved by uploading PmmC (Personality module micro Code) files. PmmC files allow the PICASO chip to be uploaded with the latest micro-Code firmware.
• System designers can incorporate the μVGA-PICASO-MD1 module directly into their application, saving space and cost. Reference designs enable the user to create a platform to incorporate the μVGA-PICASO easily.

Documents
µVGA-PICASO-MD1 Users Manual Rev. 1.2 1.15MB

µUSB-CE5
Slim USB to RS-232 bridge converter

The micro-USB μUSB-CE5 is a USB to RS-232 bridge converter which is simple, cost effective, very small and easy to use. It uses its own PCB as a card edge type connector to plug into a USB A type cable or directly into a USB hub port.

The absence of a mechanical connector makes the μUSB-CE5 a very low profile device. The design is based around the FT232RQ from FTDI and provides the user with multi baud rate serial data up to 3M baud rate. Standard 0.1” pitch 5 pin female or male header can be soldered to provide the essential signals and power to any application. RX and TX signals are both 3.3V and 5V tolerant.

Documents
µUSB-CE5 Datasheet Rev. 1 537KB

µOLED-128-GMD1 (Discontinued - use µOLED-128-G1)
1.5" Next Gen Smart OLED Display

The µOLED is a compact and cost effective all in one ‘SMART” OLED Display with an embedded graphics controller that will deliver ‘stand-alone’ functionality to your project. The ‘simple to use’ embedded commands not only control background colour but can produce text in a variety of sizes as well as draw shapes (which can include user definable bitmapped characters such as logos) in 256 or 65,536 colours whilst freeing up the host processor from the ‘processor hungry ‘ screen control functions. This means a simple micro-controller with a standard serial or USB interface can drive the µOLED module with total ease.

µOLED-128-GMD1 Features

The µOLED-128-GMD1 is aimed at being integrated into a variety of different applications via a wealth of features designed to facilitate any given functionality quickly and cost effectively and thus reduce ‘time to market’. These features are as
follows:

• 128 x 128 pixel resolution, 256 or 65K true to life colours, Enhanced OLED screen
• 1.5” diagonal. Panel Size: 45.5 x 33.5 x 8.8mm. Active Area: 27mm x 27mm.
• No backlighting with near 180° viewing angle.
• Easy 5 pin interface to any host device: VCC, TX, RX, GND, RESET
• Voltage supply from 3.3V to 6.0V, current @ 40mA nominal when using a 5.0V supply source.
• Serial RS-232 (0V to 3.3V) with auto-baud feature (300 to 256K baud). If interfacing to a system greater than 3.6V supply, a series resistor (1K) is required on the RX line.
• Powered by the fully integrated GOLDELOX-MD1 module (also available as separate OEM modules for volume users).
• Optional USB to Serial interface via the 4D micro-USB (uUSB-MB5) module.
• Onboard micro-SD (µSD) memory card adaptor for storing of icons, images, animations, etc. 64Mb to 1Gig µSD memory cards can be purchased separately.
• Three selectable font sizes (5x7, 8x8 and 8x12) for ASCII characters as well as user-defined bitmapped characters (32 @ 8x8)
• Built in graphics commands such as: LINE, CIRCLE, RECTANGLE, TEXT, USER BITMAP, BACKGROUND COLOUR, PUT PIXEL, IMAGE, etc. just to name a few

Documents
uOLED-128-GMD1 Datasheet Brief Rev. 1 133KB
uOLED-128-GMD1 Users Manual Rev. 1.3 1.18MB
uOLED Connection Diagram 14KB

µOLED-128-GMD1 Serial Command Set

The heart of the µOLED-128-GMD1 is the easy to understand command set. This comprises of a handful of easy to learn instructions that can draw lines, circles, squares, etc, to provide a full text and graphical user interface. The commands are sent to the µOLED-128-GMD1 via its serial connection (5 pin header). The command set is grouped into 3 sections:
• General Command Set
• Display Specific Command Set
• Extended Command Set

NOTE:
The RX and the TX signals are at 3.3V levels. If interfacing to a host system running at voltages greater than 3.6V levels, then a 1K series resistor must be inserted between the Host TX and the µOLED-128-GMD1 RX signals as shown in the diagram on the left.

µOLED-160-GMD1 (Discontinued - use µOLED-160-G1)
1.7" Next Gen Smart OLED Display

The µOLED is a compact and cost effective all in one ‘SMART” OLED Display with an embedded graphics controller that will deliver ‘stand-alone’ functionality to your project. The ‘simple to use’ embedded commands not only control background colour but can produce text in a variety of sizes as well as draw shapes (which can include user definable bitmapped characters such as logos) in 256 or 65,536 colours whilst freeing up the host processor from the ‘processor hungry ‘ screen control functions. This means a simple micro-controller with a standard serial or USB interface can drive the µOLED module with total ease.

µOLED-160-GMD1 Features

The µOLED-160-GMD1 is aimed at being integrated into a variety of different applications via a wealth of features designed to facilitate any given functionality quickly and cost effectively and thus reduce ‘time to market’. These features are as
follows:

• 160 x 128 pixel resolution, 256 or 65K true to life colours, Enhanced OLED screen
• 1.69” diagonal. Panel Size: 40 x 34 x 1.8mm. Active Area: 33.6 x 26.9mm.
• No backlighting with near 180° viewing angle.
• Easy 5 pin interface to any host device: VCC, TX, RX, GND, RESET
• Voltage supply from 3.6V to 6.0V, current @ 40mA nominal when using a 5.0V supply source.
• Serial RS-232 (0V to 3.3V) with auto-baud feature (300 to 256K baud). If interfacing to a system greater than 3.6V supply, a series resistor (1K) is required on the RX line.
• Powered by the fully integrated GOLDELOX-MD1 module (also available as separate OEM modules for volume users).
• Optional USB to Serial interface via the 4D micro-USB (uUSB-MB5) module.
• Onboard micro-SD (µSD) memory card adaptor for storing of icons, images, animations, etc. 64Mb to 1Gig µSD memory cards can be purchased separately.
• Three selectable font sizes (5x7, 8x8 and 8x12) for ASCII characters as well as user-defined bitmapped characters (32 @ 8x8)
• Built in graphics commands such as: LINE, CIRCLE, RECTANGLE, TEXT, USER BITMAP, BACKGROUND COLOUR, PUT PIXEL, IMAGE, etc. just to name a few

Documents
uOLED-160-GMD1 Datasheet Brief Rev. 1 125KB
uOLED-160-GMD1 Users Manual Rev. 1.1 1.08MB
uOLED Connection Diagram 14KB

µOLED-160-GMD1 Serial Command Set

The heart of the µOLED-160-GMD1 is the easy to understand command set. This comprises of a handful of easy to learn instructions that can draw lines, circles, squares, etc, to provide a full text and graphical user interface. The commands are sent to the µOLED-160-GMD1 via its serial connection (5 pin header). The command set is grouped into 3 sections:
• General Command Set
• Display Specific Command Set
• Extended Command Set

NOTE:
The RX and the TX signals are at 3.3V levels. If interfacing to a host system running at voltages greater than 3.6V levels, then a 1K series resistor must be inserted between the Host TX and the µOLED-160-GMD1 RX signals as shown in the diagram below.

More Images (click to enlarge):

µOLED-32024-PMD3 (Discontinued - use µOLED-32024-P1)
Active Matrix OLED 2.4"

µOLED-32024-PMD3T (Discontinued - use µOLED-32024-P1T)
Active Matrix OLED 2.4" with Touch Screen

µOLED-32028-PMD3 (Discontinued - use µOLED-32028-P1)
Active Matrix OLED 2.83"

µOLED-32028-PMD3T (Discontinued - use µOLED-32028-P1T)
Active Matrix OLED 2.83" with Touch Screen

Documents
uOLED-320XX-PMD3 User Manual Rev. 1.0 470KB
OLED Facts 2.69MB
S6E63D6 Driver IC Data Rev. 1.10 4.25MB

4DGL Workshop